Re: Welder advice
[Re: SleeplessKnights]
#6235401
05/07/18 08:17 PM
05/07/18 08:17 PM
|
Joined: Aug 2016
Posts: 2,855 Oklahoma
Ken Smith
trapper
|
trapper
Joined: Aug 2016
Posts: 2,855
Oklahoma
|
I use an Everlast 255ext, and an Everlast 275p mig welder. They are both great welders for the price with better duty cycles than the red and blue industrial machines.
All welders should be 220-240.( I speak as a welder), however I have a little shoulder carry century 110 stick welder and I can run 3/32 6011 rods and weld up a lot of stuff with it.
So for modifications if your gonna go mig your gonna have to have a good 220, but if you run stick you could get away with a 110 for under 150$.
And a good welder will pay for itself time and time again. More traps is always a great thing. I would recommend Bridger #2, or #3 dogless or even dogon, these traps need very little mods and can be ready with a little file work and a wax job.
Hope this helps
Matthew 7:6 KJV Give not that which is holy unto the dogs, neither cast ye your pearls before swine.... -OFBA, NTA, FTA, TTFHA-
|
|
|
Re: Welder advice
[Re: rednecktrapper]
#6235570
05/07/18 11:59 PM
05/07/18 11:59 PM
|
Joined: Jun 2010
Posts: 16,366 Iowa
~ADC~
The Count
|
The Count
Joined: Jun 2010
Posts: 16,366
Iowa
|
My best piece of advice is to buy a bigger welder than what you think you need right now, and definitely get one with a gas bottle.
x2!
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6235600
05/08/18 01:49 AM
05/08/18 01:49 AM
|
Joined: Mar 2011
Posts: 25,409 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,409
williams,mn
|
If need be, I can do a trap mod with my old Lincoln 225 stick welder. And fairly ugly too .
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6235738
05/08/18 10:15 AM
05/08/18 10:15 AM
|
Joined: Aug 2011
Posts: 1,971 Peoria County Illinois
Larry Baer
trapper
|
trapper
Joined: Aug 2011
Posts: 1,971
Peoria County Illinois
|
I bought a 110 volt Hobart wire feed welder to weld Aluminum for work. I have been also using it for traps on weekends. Works great but- I'm with the other guys in the sense that you should buy a bigger one than what you need.
Just passin through
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6236005
05/08/18 06:22 PM
05/08/18 06:22 PM
|
Joined: Apr 2012
Posts: 5,445 Southern Michigan
trappergbus
trapper
|
trapper
Joined: Apr 2012
Posts: 5,445
Southern Michigan
|
Figure in the cost of the mods needed and add that figure to the cost of the traps per dozen. Then decide if you want a trap that needs mods or a trap that doesn't, for very close to the same total cost..
Common sense catches alot of fur.. Pay homage to all you harvest..
|
|
|
Re: Welder advice
[Re: Larry Baer]
#6236227
05/08/18 11:44 PM
05/08/18 11:44 PM
|
Joined: Dec 2014
Posts: 1,222 MN
yukonal
trapper
|
trapper
Joined: Dec 2014
Posts: 1,222
MN
|
I bought a 110 volt Hobart wire feed welder to weld Aluminum for work. I have been also using it for traps on weekends. Works great but- I'm with the other guys in the sense that you should buy a bigger one than what you need. This is what I have, with gas. I have used it for ALL kinds of trap mods, and it has WAY more oomph than you need for that application. I have also used it for all kinds of welding projects around the shop...welding up to 1/4" steel, and built dozens of 1/2" stakes as well. Totally disagree about a bigger model to do trap mods. But...to answer your question from the top...if it is only to do trap mods, buy the best trap you can, and forget about spending all that extra time and money working on cheaper ones. Now, if you have a bunch of extra time and money, and really WANT to do it, then a 110 Hobart mig welder with an argon tank will do anything you want with traps, and be rewarding as well.
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6236555
05/09/18 03:03 PM
05/09/18 03:03 PM
|
Joined: Aug 2015
Posts: 38 north dakota
k9gter
trapper
|
trapper
Joined: Aug 2015
Posts: 38
north dakota
|
Go with the everlast powermts 221sti they are running a special $700 off the price on there website its a AC/DC Mig tig and stick all in one unit first of its kind. You will love it i can promise u this
"live like its your last day on earth" "Don't bring yesterdays problems into today"
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6236685
05/09/18 05:51 PM
05/09/18 05:51 PM
|
Joined: Dec 2006
Posts: 21,028 St. Louis Co, Mo
BigBob
trapper
|
trapper
Joined: Dec 2006
Posts: 21,028
St. Louis Co, Mo
|
40 + years a machinist, and most shops use a Lincoln 225 unless they do a lot of fab work.
Every kid needs a Dog and a Curmudgeon.
Remember Bowe Bergdahl, the traitor.
Beware! Jill Pudlewski, Ron Oates and Keven Begesse are liars and thiefs!
|
|
|
Re: Welder advice
[Re: SleeplessKnights]
#6236722
05/09/18 07:12 PM
05/09/18 07:12 PM
|
Joined: Dec 2006
Posts: 23,830 Wisconsin
The Beav
trapper
|
trapper
Joined: Dec 2006
Posts: 23,830
Wisconsin
|
I have Miller thunder bolt Stick welder. I see them on sale for around #400.00
The forum Know It All according to Muskrat
|
|
|
|
|