Re: Anyone Cast Bullets ?
[Re: Paul D. Heppner]
#6888401
06/02/20 03:15 PM
06/02/20 03:15 PM
|
Joined: Jul 2013
Posts: 11,894 Amite county Mississippi
Wolfdog91
OP
trapper
|
OP
trapper
Joined: Jul 2013
Posts: 11,894
Amite county Mississippi
|
Yeah I'm about to start dipping my toes into it. Joined cast boolits to see if i could get a good footing and welllll.. the guys are great and try to be helpful but I feel like I'm in a collage master class listening to some of these advice, pretty overwelming at times lol. Also want to see if Any of y'all had a lee .225 mold and sizing kit I could buy, all the supply house are backed up and I'm a little inpatient lol. Planning on trying to make some .223's power coating them and using then for my AR nothing super fancy but I am considering do some videos on me bumbling my way though all of this ( not a how to ) since there's not many if them . Figured it be somthing interesting to watch
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888575
06/02/20 06:29 PM
06/02/20 06:29 PM
|
Joined: May 2011
Posts: 849 Michigan
coonlove
trapper
|
trapper
Joined: May 2011
Posts: 849
Michigan
|
Wolfdog, get a copy of the Lyman cast bullet handbook-lots of info and load data. I used to cast and load for a couple of .222s but it has been a while. Bullets need to be fairly hard and gas checked and velocity kept to around 2,000 FPS. I'm sure there are better lubes around these days also. Used to be a cheap way to shoot, not so much anymore. Dive in and enjoy.
P.S. less than full power loads may not function an autoloader.
Last edited by coonlove; 06/02/20 06:30 PM.
"I'm the paterfamilias"
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888617
06/02/20 07:05 PM
06/02/20 07:05 PM
|
Joined: Oct 2015
Posts: 3,077 Wyoming
cmcf
trapper
|
trapper
Joined: Oct 2015
Posts: 3,077
Wyoming
|
When you say powder coat are you talking moly?
“The world is governed by very different personages from what is imagined” B. Disraeli
|
|
|
Re: Anyone Cast Bullets ?
[Re: cmcf]
#6888652
06/02/20 07:30 PM
06/02/20 07:30 PM
|
Joined: Sep 2013
Posts: 18,598 Green County Wisconsin
GREENCOUNTYPETE
trapper
|
trapper
Joined: Sep 2013
Posts: 18,598
Green County Wisconsin
|
When you say powder coat are you talking moly? no very specifically Harbor Freight Red powder coating , baked on cast boolits and sized a half inch of the black air soft BBs in about a 3-4 quart #5 recyclable food container two table spoons to get started and then about a table spoon per every 100-150 boolits , about 75 boolits of 9 or 40 and less if bigger with lid on shake vigorously up and down , then using a disposable glove I rub the 3 fingers I use to pick the boolits up in powder coating then pick up and set base down boolits on parchment paper on cookie sheets that go in my small convection oven , 10 minutes at 400 bakes the coating on nicely. let them cool and run through the sizing die the next day no lube the coating ios slipery enough , then load the 2 different typse of plastic creat a static charge and make the powder cling to the boolits being agitated with the powder and BBs I can't take any credit for this idea got it form cast boolits http://castboolits.gunloads.com/for...s&s=d594f0464927d643299e5cd0a893e38aI mostly do 9mm and size .356 when I don't have time I buy Acme HiTech coated boolits http://www.acmebullet.com/bullets-reloading-brass/9MM-Lead-Cast-Reloading-Bullets?product_id=424I cast about 124 gr and load my own or acme over the same charge of powder notice no difference which I am running .
America only has one issue, we have a Responsibility crisis and everything else stems from it.
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888707
06/02/20 08:06 PM
06/02/20 08:06 PM
|
Joined: Oct 2015
Posts: 3,077 Wyoming
cmcf
trapper
|
trapper
Joined: Oct 2015
Posts: 3,077
Wyoming
|
Thanks GCP Never heard about that. I’m set up for moly same basic process does a great job on cast as well as jacketed. Higher velocities without higher pressures. Vibratory tumbler some #2 steel shot tablesp of moly and boolets. Cuts down on copper and lead fowling.
“The world is governed by very different personages from what is imagined” B. Disraeli
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888795
06/02/20 09:38 PM
06/02/20 09:38 PM
|
Joined: Sep 2013
Posts: 18,598 Green County Wisconsin
GREENCOUNTYPETE
trapper
|
trapper
Joined: Sep 2013
Posts: 18,598
Green County Wisconsin
|
I know HF red isn't the best or even that good but when I started It was easily available and didn't cost much. I bought one then 2 or 3 and it goes a long way I haven't run out yet
fatter bullets are easier to cast and load
a .312 mold for your 7.62x39 wouldn't be a bad place to start , 30-30 is a good place to start if you have one 35 cal is good as is 45
I have a friend who casts and loads the .225 bullet in 223rem, but he shoots them from a 1:14 twist AR he also only loads to about 2400fps
bigger calibers also tend to have slower twist rates slower twist is more forgiving to cast and since your not really pushing high velocities
America only has one issue, we have a Responsibility crisis and everything else stems from it.
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888851
06/02/20 10:43 PM
06/02/20 10:43 PM
|
Joined: Feb 2009
Posts: 828 Hill City,Mn.
Rally
trapper
|
trapper
Joined: Feb 2009
Posts: 828
Hill City,Mn.
|
What Paul said. All good advice, especially not starting with .22 cal. There are guys using Ar’s and cast, but they have a lot of experience and still have troubles.
Keep your boots dry
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6888979
06/03/20 07:44 AM
06/03/20 07:44 AM
|
Joined: May 2010
Posts: 2,738 Iowa
coydog2
trapper
|
trapper
Joined: May 2010
Posts: 2,738
Iowa
|
I do casting on boolits and also some buck shot and sinkers. Wolfdog do not let it get you on cast boolit for how it is there you will learn in time on there I know try to learn too much at once. Like state about the Lyman cast book will help you the best and then go from there .If you able to find the 3rd Edition of it you will learn more on it , I do the old way of size and lube my boolits.I do 22cal for my 22-250 . If you look to load for semi auto Lyman dose have a manual on it that have jacket and cast bullets data.
Life member of DAV,NTA,NRA,ITA.Also member of FTA,CBA
|
|
|
Re: Anyone Cast Bullets ?
[Re: Wolfdog91]
#6889061
06/03/20 09:25 AM
06/03/20 09:25 AM
|
Joined: Dec 2010
Posts: 4,831 central arkansas
the Blak Spot
trapper
|
trapper
Joined: Dec 2010
Posts: 4,831
central arkansas
|
I do. Heres a lyman 452423 from a uberti 45 colt single action
the just shall live by faith
member FTA, ATA, EAFT 1776 - the year we told a tyrant we weren't to be under a dictator Caveat ater macula
|
|
|
|
|