I was able to get a 12 in piece of pvc 6 ft long. I'm not sure what dimension's to draw on it prior to cutting it. I want to cut it in half,diameter wise, and use one half for yotes and cats. The other half for beaver. I'll do coon on which ever side will work the best.

I want to make one fleshing stand and build it so the pvc is interchangeable.

Any and all suggestions are welcome, thanks!

Check out CoonCreek on youtube in his older videos he has a how he made his with sizes. I made my off of his.

I would make one end for large critters and the other end for small critters, if it was me.
The base would accommodate swapping ends.

The base would either be a 4 x 4 or a 6 x 6.

I used a wire stretcher for a pattern on an 8" piece of pvc pipe. Then made a wooden base that I could remove the pvc and store away until I needed it again.

I did watch Coon Creek but I didn't see anything about the size. I heard him refer to them by the pelt. I'll go back and look I may have missed it

I used a coon stretcher for a pattern. Made 3 different sizes, but just use the coon size 99% of the time. I'm just doing coyotes and coons most of the time. I think I made mine 6 years ago, really has worked well for me. Made sure you wear a mask when cutting and forming.

LDW you used a coon stretcher for you pattern, does that seem to work good on your coyotes? You made three different sizes what did you use for the other two?

I used a coon to make mine and really don't see the need for me to make any other size for my needs.

Buddy dropped one off for my 4H class to use this weekend it has 3 different slip on beams for different head width sizes and beavers. He said if it gets a gouge mark just smooth it out with a torch to smooth it out.

I tried one for beaver, the hide kept sliding off the side.

Can i use a 2" pvc pipe(not cut) to flesh mink?

I just flesh mink on the same board that they will dry on. Just cut a slot in a big chunk of wood to hold the board up at an angle on your table. I just use a big chunk of 6x6 for the base.

For rats I use a long fox stretcher leaned against a table, or a muskrat board in the same slot I put my mink board in...

A pelt scraper is easier than a big fleshing knife on these 2 animals in my opinion. A big serving spoon works fine.

That’s a cool and easy fix!

Yep, the coon board works great for coyotes. I made a board 12 inches wide for beaver and a narrow one for rats and mink. I never use those 2 as I just trap coyotes along with coons that plug up my yote sets.

ttt

I fleshed a 65lb beaver this morning on a 7" beam. Never again, need a wider beam for those big beavers. He was an old warhorse and after removing the saddle and all the fat he had multiple scars from fighting over the years. I've got to find some of that pipe so I can modify my beam.

My buddy has 3 different slip on beams for his from beaver to muskrats just snap one off then snap the other one on.

Owen156 I was driving by a construction site and saw a bunch of pvc laying around. I stopped and spoke with the site foreman asked him if I could buy a piece of there pvc if they had any scrapes left over. After about 20 minutes of bs'ing he said follow me. He took me to a pile and asked me if I wanted 10in or 12in. I told him I'd like the 12in and asked him how much he told me nothing. It was about 6ft long I went to lift it and it was pretty heavy he said leave it I'll have my guy load it. He called out to some young kid to load for me and that fellow picked it up and put it on his shoulder and loaded it into the bed of my truck and that's all there is to getting a piece of pvc pipe.

What does the beaver beam look like as far as width and shape?

I’ll go get a pic, looks like one is 6 3/4 the other wide one is 5 1/2 then the smaller beam. Looks like he uses the middle one the most.




I’m making mine different as far as the base goes I’m thinking a folding treated post that comes up short at the top to allow the use of a thinner rat beam with no added material from the support post under it. A hinge and bolt through the bottom base would allow it to go up and down and when in the up position the board piece would fit into a slot to hold it in place that’s on the hinge.