Usually I buy Oregon chains. I was just wondering what other brands people prefer and why? I'm running a 20", 3/8, .050 Semi Chisel, Semi Skip

Only brand I know is Oregon.

It depends on the saw / bar combination ....... For general messing around. I use a 063 full chisel full comp Archer chain that I buy on a roll and spin up my own. For milling I use a modified 050 full chisel Stihl chain. All of them 3/8"...... Bar length from 18 to 36" Mostly the 36" Tsumura light bar.
On the little saw a semi chisel 050 325.

Anything but Stihl. It's hard and eats up my files.
Have grinder but rarely use it.

I sharpened 20 chains this morning. I like the Stihl chains better than Oregon chains (I use Echo saws). We do quite a bit of chainsaw work.

The Stihl seem to hold up better.

Our posts crossed. I switched to a grinder a few years ago.

Stihl chains, especially when I can catch them on Sale.

My grinder is a free Hazard Fright model.
I use it for rocked chains but don't have much faith in it.

For semichiz I was liking Carlton chain but the supplier I liked retired, and I do not see it.
I liked the Archer ok too. Like Scoob said, it depends.

Stihl saw and stihl chains.

less about who and more about what type of chain for me

I prefer full chisel with semi chisel being next I want nothing to do with your safety chain low kick back stuff

Carlton , Oregon , woodland pro which is basically a rebranded carlton sold by Baylies online , and huskivarna are all good chains I don't own Stihls any more and they only sell the low kick back stuff at the lcoal dealer

I hand file my own once I have filed it I am not sure I can tell any difference between the Carlton and oregon the local saw shop carries spools of either depending on the day and what he could get for stock.

I am 3/8 .058 on my saws so I only need one chain

If you're running a 20 inch bar or longer switch to a full skip.

I run three types of chains.

My favorite is stihl yellow chains, yes you almost need a grinder to keep them sharp. I also like the Husquvarna X-cuts. The majority of my chains our oregon - they are cheap, soft, and i feel they need the most attention. I have considered switching my chains to carbides, but the $200 i would have to spend on the grinding wheel to keep them sharp has made me not switch.

Can I ask, what is an easy way out of the low pro on a ms 170?
Not impressed with that chain at all.

I feel full skip or even semi skip chains are not for saws running smaller bars then 24”. I’d run full comp full chisel chain. Husky chain and Oregon are nice both made in the same factory Oregon owned unless that’s changed. I like stihls yellow or there super square ground. Get a couple loops of square ground and a few good files you’ll never go back to round. Square cuts way faster. Stihl chains are harder on files but I buy files by the ten pack. For dirty wood semi chisel shines for it can take a little more abuse. But all in all keep your chain sharp and they all do pretty well. But stihl chain comes out the box sharper stays sharp longer unless you rock it and the chain life seem to be longer then other brands just imo.

I like Oregon chain on my 20" bar Huskvarna. Seems to me the chain tooth is longer and will take a lot of sharpening before it is toast. Economical and available too. I am no pro, though!

Chris

Skip chains kick back bad if you try to make plunge cuts, I always plunge cut when sawing down trees over 24". gives me added security when working alone in the woods.

There isn't really an option for a better chain on a ms170. That saw is specifically designed for home owners, and it really wouldn't have enough power to turn a more aggressive chain if there was an option.

That little 170 does not have the oomph to run a chain with higher chip clearance volume. I could however make you an adapter to turn it into a margarita mixer

Thanks guys. It'll probably get sold to a Stihl is great fan lol.

LOL.

ive tried a couple of the archer chains on my husky 372xp & so far they seem to hold up just as good as the oregons ive used in the past, i buck about 7 to 10 cord of mixed hardwood a year. 20" 3/8 .058 gauge full chisel.
they were quite a bit cheaper but it looks like the price has gone up quite a bit like everything else.