Re: Tile set up for mink?
[Re: hogwild]
#6383301
11/27/18 09:03 AM
11/27/18 09:03 AM
|
Joined: Dec 2006
Posts: 23,854 Wisconsin
The Beav
trapper
|
trapper
Joined: Dec 2006
Posts: 23,854
Wisconsin
|
Good luck. The problem your going to have Is getting the mink to go through the body grip . Now If you cut out a section on the bottom lip of the tile so you could bed a foot hold part way In the tile you might have more success.
The forum Know It All according to Muskrat
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384010
11/27/18 11:14 PM
11/27/18 11:14 PM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
I haven't tried tile yet. I set out 5 of these on Saturday and am 3 for 5 so far. I need to set 300, lol. They'll go through a conibear but don't care for a hard trigger right in their face.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384026
11/27/18 11:32 PM
11/27/18 11:32 PM
|
Haggard
Unregistered
|
Haggard
Unregistered
|
Nice Les! I've never could get mink to push through the wires either. Pans on conis are nice. Thanks for starting this thread. I never quite understood what a tile was. Not kidding either. I use to think it was the rip/rap the water fell on, not what we call pipe over here. Man I'm not too sharp
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384032
11/27/18 11:44 PM
11/27/18 11:44 PM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
Most of my conis have a bell trigger with mono between the wires in a loose loop, and held on with silicon tubing. I like this set up better. Both the pan trigger traps allowed for a suit case catch too far back, the mink was shoulders through the trap, but the bell trigger smoke him to the head.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384042
11/27/18 11:55 PM
11/27/18 11:55 PM
|
Haggard
Unregistered
|
Haggard
Unregistered
|
There sure more than committed with the pan. We are getting hut with rain hard. My traps had 2 inches of new snow on top of them too. Maybe I will go set boxes tomorrow.
I think I have some 8 inch pipe scrap like that. I was going to save it for little concrete piers. I like hoarding stuff
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384066
11/28/18 01:28 AM
11/28/18 01:28 AM
|
Joined: Dec 2006
Posts: 5,570 La Crosse, WI
Macthediver
trapper
|
trapper
Joined: Dec 2006
Posts: 5,570
La Crosse, WI
|
I had dozen RBGs made to fit perfect in the 4inch tile. Never did get a mink to stick their melon in one. Had the triggers circle the edge, maybe should look at trying pans on those.
Mac
"Never Forget Which Way Is Up"
|
|
|
Re: Tile set up for mink?
[Re: fossil2]
#6384070
11/28/18 01:41 AM
11/28/18 01:41 AM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
trapper les,,,ive never tried a box of that design before. best I can tell from the pics, the trap goes in the back of the box, then the bait, then close the back end of the box. entry hole on the opposite end? is this correct? also, are you using a 3 1/2 inch entry hole? seems like a nice design to exclude coon. thanks!!! tim Here is a better picture. The back is screened in, and the bait (this year its venison tallow and boning scraps) and I added another spring to make them 120s. It's a 2 3/4 inch hole at the top of a swinging door. During fisher/maten season, I leave the doors up, as those characters will somehow stick their head in the trap once in a while, and it will still catch mink.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384072
11/28/18 01:44 AM
11/28/18 01:44 AM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
At this point, I'd like to apologize for derailing the thread, sort of.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384358
11/28/18 12:15 PM
11/28/18 12:15 PM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
I make is about a 2 1/2" round hole, and the tag ends of my mono finish the visual loop above even though they aren't attached to anything. The mink darts through the mono loop and it acts like a soft belly catch. There is no need for a "hard loop" that is detectable that they can climb around.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
Re: Tile set up for mink?
[Re: hogwild]
#6384725
11/28/18 08:16 PM
11/28/18 08:16 PM
|
Joined: Mar 2011
Posts: 25,417 williams,mn
trapper les
trapper
|
trapper
Joined: Mar 2011
Posts: 25,417
williams,mn
|
Clay, the tag ends aren't attached at the top of the loop, they just form one inside the realm of the wires. A little circle within the wire bell, only held by the sides.
"Those who hammer their guns into plowshares will plow for those who do not."
|
|
|
|
|