Strictly Trapping


No Profanity *** No Flaming *** No Advertising *** No Anti Trappers *** No Politics
No Non-Target Catches *** No Links to Anti-trapping Sites *** No Avoiding Profanity Filter


Home~Trap Talk~ADC Forum~Trap Shed~Wilderness Trapping~International Trappers~Fur Handling

Auction Forum~Trapper Tips~Links~Gallery~Basic Sets~Convention Calendar~Chat~ Trap Collecting Forum

Trapper's Humor~Strictly Trapping~Fur Buyers Directory~Mugshots~Fur Sale Directory~Wildcrafting

Trapper's Tales~Words From The Past~Legends~Archives~Kids Forum~Lure Formulators Forum


~~~ Dobbins' Products Catalog ~~~


Trading Post
(Please support F&T Trading Post, our sponsor for the Trapping Only Forum)



TrappersPost
Please support Trappers post, a sponsor of the Strictly Trapping Forum



Print Thread
Hop To
Slider Rods for Coon in an odd Situation??? #6575060
07/16/19 04:59 PM
07/16/19 04:59 PM
Joined: Feb 2009
Posts: 1,593
KY
A
AnthonyT Offline OP
trapper
AnthonyT  Offline OP
trapper
A

Joined: Feb 2009
Posts: 1,593
KY
I have a new area to coon trap this fall. All of the waterways on it are very deep, wide, sloughs that drain ag fields.The edge is a few inches to a foot deep, but more than a step in is over your head. Would a drowner rod anchored at the bank and angled downstream (good amount of current in these sloughs) and set so the rod is under water but the deep end is free work for coon, rats and mink? Might get on occasional otter or beaver, but would targeting coon. I'm thinking the weight of the trap plus the current would do the job.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575140
07/16/19 07:52 PM
07/16/19 07:52 PM
Joined: Dec 2014
Posts: 2,930
E central Il
G
Golf ball Offline
trapper
Golf ball  Offline
trapper
G

Joined: Dec 2014
Posts: 2,930
E central Il
Can you not drive the rod into the bottom ?

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575149
07/16/19 08:02 PM
07/16/19 08:02 PM
Joined: Aug 2015
Posts: 829
NE NE
W
Wife Offline
trapper
Wife  Offline
trapper
W

Joined: Aug 2015
Posts: 829
NE NE
Rod has to be fairly stiff. Use 1/2" rebar minimum and have 2 anchor points at the bank end (2 washers welded to rebar about 1' apart -- anchor with stakes). The water end of the rebar does not have to be driven into the bottom if coon is the catch but an otter or beaver will bend the rod if not secured (driven ) in the water.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575163
07/16/19 08:16 PM
07/16/19 08:16 PM
Joined: Feb 2009
Posts: 1,593
KY
A
AnthonyT Offline OP
trapper
AnthonyT  Offline OP
trapper
A

Joined: Feb 2009
Posts: 1,593
KY
You would be lucky to hit the bottom with a 10 foot rod, and if you could it is nothing but loose silt muck. The rod would never hold.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575177
07/16/19 08:44 PM
07/16/19 08:44 PM
Joined: Dec 2006
Posts: 17,550
Rodney,Ohio
SNIPERBBB Offline
trapper
SNIPERBBB  Offline
trapper

Joined: Dec 2006
Posts: 17,550
Rodney,Ohio
If you can double stake the top of the rod so it can't swivel it will work. But if a back foot beaver or otter get in it, you might have a pretzel when you come back.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575217
07/16/19 09:27 PM
07/16/19 09:27 PM
Joined: Dec 2006
Posts: 11,165
Central NC
T
traprjohn Offline
trapper
traprjohn  Offline
trapper
T

Joined: Dec 2006
Posts: 11,165
Central NC
When I can't get a 12 ft rod into the bottom, I put about 30 lbs of weight at the rods bottom...double t-stake the top.

You could be better off going old school with a weight on bottom and wire to shore...as shown in the Basic Sets forum here, click on Castor Mound Set for sketches of weight an slide wire.


www.sevenoakstrappingsupplies.com for trap mods and gear
The 10 Commandments are not suggestions.
Buy a soldiers meal EVERY chance you can.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575598
07/17/19 01:31 PM
07/17/19 01:31 PM
Joined: Aug 2011
Posts: 1,968
Peoria County Illinois
Larry Baer Offline
trapper
Larry Baer  Offline
trapper

Joined: Aug 2011
Posts: 1,968
Peoria County Illinois
cable with a weight on the bottom


Just passin through
Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575608
07/17/19 02:00 PM
07/17/19 02:00 PM
Joined: Dec 2015
Posts: 677
northern indiana
K
kenny k Offline
trapper
kenny k  Offline
trapper
K

Joined: Dec 2015
Posts: 677
northern indiana
I would not use weight ,you mite not get it back. The muck ditches here I lost some brake rotors I could get out of muck.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575629
07/17/19 03:08 PM
07/17/19 03:08 PM
Joined: Feb 2009
Posts: 1,593
KY
A
AnthonyT Offline OP
trapper
AnthonyT  Offline OP
trapper
A

Joined: Feb 2009
Posts: 1,593
KY
Kenny, that is my thought exactly and why I asked about the free floating rod.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6575679
07/17/19 04:41 PM
07/17/19 04:41 PM
Joined: Dec 2006
Posts: 20,966
St. Louis Co, Mo
B
BigBob Offline
trapper
BigBob  Offline
trapper
B

Joined: Dec 2006
Posts: 20,966
St. Louis Co, Mo
Seems to me the current flow would make the catch rise up to the top without a fairly heavy weight, or a drowner wire.


Every kid needs a Dog and a Curmudgeon.

Remember Bowe Bergdahl, the traitor.

Beware! Jill Pudlewski, Ron Oates and Keven Begesse are liars and thiefs!
Re: Slider Rods for Coon in an odd Situation??? [Re: SNIPERBBB] #6575993
07/17/19 11:22 PM
07/17/19 11:22 PM
Joined: Jun 2010
Posts: 16,261
Iowa
~ADC~ Online content
The Count
~ADC~  Online Content
The Count

Joined: Jun 2010
Posts: 16,261
Iowa
Originally Posted by SNIPERBBB
If you can double stake the top of the rod so it can't swivel it will work.


This. Put on stake at the end and one 18" from the end so it can't turn, or you can push the end of the drowner into the bank below the set and put your stake out part way down the rod. Coons and even big beaver can't get much traction in open water. They won't last long.

[Linked Image]

Re: Slider Rods for Coon in an odd Situation??? [Re: BigBob] #6576013
07/18/19 12:31 AM
07/18/19 12:31 AM
Joined: Feb 2016
Posts: 849
Washington
wildflights Offline
trapper
wildflights  Offline
trapper

Joined: Feb 2016
Posts: 849
Washington
Originally Posted by BigBob
Seems to me the current flow would make the catch rise up to the top without a fairly heavy weight, or a drowner wire.


There have been swift water rescue swimmers that have drowned in shallow water. Even when on a tether in a strong current. Water flow doesn't make you float.

Last edited by wildflights; 07/18/19 12:33 AM.

Tradition is not the worship of ashes, but the preservation of fire. -Gustav Mahler
Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6576052
07/18/19 06:14 AM
07/18/19 06:14 AM
Joined: Dec 2006
Posts: 5,444
Wisconsin
Muskrat Offline
trapper
Muskrat  Offline
trapper

Joined: Dec 2006
Posts: 5,444
Wisconsin
I trapped a river for many years that had the same physical conditions. Maybe a couple inches deep for a foot or so, then dropped off to eight feet or more. I struggled with cables and drowner weights, and finally went with drowner rods.

The rods were 10' lengths of 3/8" rerod. A slider lock was on the rod, designed to go one way. A nut was welded onto the terminal end to keep the slide from coming off. Eighteen inches from the bank end, a nut was welded onto the side of the rod. The nut was big enough to allow a 24" length of 3/8" stake to go through.

Now, time to set. The trap was S-linked onto the drowner lock. Angling the rod with the current slightly, the rod was pushed into the bank, horizontally, so the 18" of rerod was stuck into the bank, and pushed in until the side nut was just at the bank. The trap stake was shoved through the nut, and the set was made. Pocket, pipe, blind, etc.

The theory was the critter would get into the trap, slide its way out onto the rod, and the end of the rod with trap and critter would be heavy enough to dispatch the critter. And it worked.

Couple of things to keep in mind:

1) make darned sure there's nothing out there to hang up the rod from dropping down. No logs, no stumps, etc. I recall this one big boar 'coon that greeted me by waving to me as I was checking the sets one evening from the boat. He had slid out, gained traction with a log, then curled that 3/8" rerod right over into a huge arc. Was standing on the bank with his paw up in the air waiting for me. That taught me to check for sure there were no obstructions.

2) use a trowel to dig under the rod in the shallow water to be sure the slider can slide. A muskrat or mink may hang up if the slider can't move properly.

Shared this technique with many other water trappers. Most of 'em poo pooed it, said it wouldn't work. Well, it worked for me for 20+ years in this stretch of river. But only for those sets that dropped right off.

When trapping beaver I went traditional to 1/2" rerod that stuck into the bottom or went with cable and weights. Didn't trust the 3/8" rerod.

I hope this helps you out. PM me if you have more questions about this particular technique. I trapped out of a boat and it was easy to have 25 of these rods on each side of the boat when starting a stretch of the river.

Today I trap a different river under different conditions and no longer have this horizontal drowner rod employed. I cut all the 10' sticks in half and have employed them as a vertical short terminal rod with a hammer pipe and am very pleased with the setup.


Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6576224
07/18/19 10:55 AM
07/18/19 10:55 AM
Joined: Feb 2009
Posts: 1,593
KY
A
AnthonyT Offline OP
trapper
AnthonyT  Offline OP
trapper
A

Joined: Feb 2009
Posts: 1,593
KY
ADC and Muskrat - that is what I was looking for!

Muskrat, do you have a pic of how your short rod setup works? I trap some other waterways that they may work on.

Thanks!

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6576243
07/18/19 11:41 AM
07/18/19 11:41 AM
Joined: Dec 2006
Posts: 5,444
Wisconsin
Muskrat Offline
trapper
Muskrat  Offline
trapper

Joined: Dec 2006
Posts: 5,444
Wisconsin
Anthony T, I'll try and get something together tonight.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6576425
07/18/19 05:47 PM
07/18/19 05:47 PM
Joined: Jul 2013
Posts: 11,775
Amite county Mississippi
Wolfdog91 Offline
trapper
Wolfdog91  Offline
trapper

Joined: Jul 2013
Posts: 11,775
Amite county Mississippi
Why not just a larger trap and a long chain ?

Re: Slider Rods for Coon in an odd Situation??? [Re: Wolfdog91] #6576513
07/18/19 07:52 PM
07/18/19 07:52 PM
Joined: Dec 2006
Posts: 5,444
Wisconsin
Muskrat Offline
trapper
Muskrat  Offline
trapper

Joined: Dec 2006
Posts: 5,444
Wisconsin
Originally Posted by Wolfdog91
Why not just a larger trap and a long chain ?


I don't go with larger traps since I want my 'rats and mink down and out of sight. If they're up in the shallows caught in a larger trap they can't move they're gong to be fed upon before I check the sets.

Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6576526
07/18/19 08:13 PM
07/18/19 08:13 PM
Joined: Dec 2006
Posts: 5,444
Wisconsin
Muskrat Offline
trapper
Muskrat  Offline
trapper

Joined: Dec 2006
Posts: 5,444
Wisconsin
Anthony T -- short rod set up.

Here's the short rod. 5 foot stick of 3/8" rerod. There's a nut smashed onto the rerod, looks to be about 24" down from the end. The end that is on the street is the top, The bottom end is in the bed of the truck. The pipe to the left is the "hammer pipe". I have an S-hook attached to the end of a drowner cable. That way the 3/8" rerod can slide through it. Slide it through, push it into the substrate, and use the pipe to hammer it down. Doesn't work in rock.

[Linked Image]

Here's a shot of that rerod going through the S-hook to secure the end of the drowner cable. This is an older pic and I've changed something since that I'll mention a little later.

[Linked Image]

You can set these DPs anywhere in a drowning situation so long as there's no entanglement from the trap to the terminal end of the cable.

[Linked Image]

River dropped a foot plus one day and the eagles had snackums.

[Linked Image]

Look at the 'coon sign on this bank. I usually have 4-6 Dps on this bank alone.

[Linked Image]

Now, in this pic there are two sets. One of 'em scored a 'coon as you can see in the water. Both sets have a DP and both DPs are cabled to one terminal short rod. In situations like this I will grab a 10' cable and a 15' cable. Both are anchored at the set location with a 24" or 18" length of rerod, depending on substrate. The longer cable, in this case the 15 footer, is the upstream cable. Wearing chest waders, I will grab one short rod, the hammer pipe, and the ends of both cables. I'll walk out holding the ends of the cables and when both are tight, I'll slide that rerod through both S-hooks and push it into the substrate. Then take the pipe and hammer that down. Remember, the nut with about 24" of rerod above it is the top of the rod.

[Linked Image]

In the boat there are four milk crates. One has 6' lengths, another 10', 15' and 20'. There's a bucket in the back with "specials" that have 30s, 40s, and 50 footers. In some cases I slide 'coon over sandbars 'til I get to deeper water.

Now, the change to that second pic that I mentioned earlier. You can see how that 'coon can slide all the way to the terminal rod. I've had them power out using the rod as leverage. To solve that I cut off the end and slid a stop onto the cable. Hammered it down and then finished the cable with the double ferrule and an S-link. I've experimented with different lengths and have come up with 30" as a distance from the end of the cable to keep 'coon from powering out. The 6 footers have their stop at 24".

This is what works for me. You can make a hundred sets with 50 short rods in the boat, setting everything in pairs. When I'm trapping deeper water than I can wade out into I incorporate 10' sticks with the same setup. Or go with a drowner weight.

Anyway, for what it's worth.


Re: Slider Rods for Coon in an odd Situation??? [Re: AnthonyT] #6577021
07/19/19 01:25 PM
07/19/19 01:25 PM
Joined: Feb 2009
Posts: 1,593
KY
A
AnthonyT Offline OP
trapper
AnthonyT  Offline OP
trapper
A

Joined: Feb 2009
Posts: 1,593
KY
Muskrat, thanks for the great pics and explanation. I could use that system on some of the other creeks I trap. I also have to deal with eagles and they will grab any critter that is not under the water.

Previous Thread
Index
Next Thread

Moderated by  Drifter, Wolfdog91 

Powered by UBB.threads™ PHP Forum Software 7.7.1