Auger Bit For Rotary Hammer Drill - Trapperman Forums

Strictly Trapping

No Profanity *** No Flaming *** No Advertising *** No Anti Trappers *** No Politics
No Non-Target Catches *** No Links to Anti-trapping Sites *** No Avoiding Profanity Filter

Home~Trap Talk~ADC Forum~Trap Shed~Wilderness Trapping~International Trappers~Fur Handling

Auction Forum~Trapper Tips~Links~Gallery~Basic Sets~Convention Calendar~Chat~ Trap Collecting Forum

Trapper's Humor~Strictly Trapping~Fur Buyers Directory~Mugshots~Fur Sale Directory~Wildcrafting

Trapper's Tales~Words From The Past~Legends~Archives~Kids Forum~Lure Formulators Forum

~~~ Dobbins' Products Catalog ~~~

(Please support F&T Trading Post, our sponsor for the Trapping Only Forum)

Please support Trappers post, a sponsor of the Strictly Trapping Forum

Register Log In Home Forums Trapping Only Auger Bit For Rotary Hammer Drill

Print Thread

Hop To

Auger Bit For Rotary Hammer Drill #6632473 10/04/19 09:31 AM 10/04/19 09:31 AM
Joined: Dec 2014 Posts: 1,222 MN Y yukonal OP trapper
yukonal OP trapper Y Joined: Dec 2014 Posts: 1,222 MN	Does someone make an auger bit that will fit the slotted chuck teeth on a rotary hammer drill? I currently use a 1/2" cordless drill, with an auger bit that has a 3/8" shank. Upgrading to a rotary hammer drill.

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6632537 10/04/19 10:53 AM 10/04/19 10:53 AM
Joined: Jan 2007 Posts: 5,459 Montana Taximan trapper
Taximan trapper Joined: Jan 2007 Posts: 5,459 Montana	Not enough information.Exactly what type of bit does your tool use?

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6632638 10/04/19 02:16 PM 10/04/19 02:16 PM
Joined: Mar 2016 Posts: 2,162 N.E. Nebr L LDW trapper
LDW trapper L Joined: Mar 2016 Posts: 2,162 N.E. Nebr	I went to Harbor Freight and bought a cheap SDS bit, cut the end off and welded to my auger. Done deal.

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6632651 10/04/19 02:35 PM 10/04/19 02:35 PM
Joined: Dec 2014 Posts: 1,222 MN Y yukonal OP trapper
yukonal OP trapper Y Joined: Dec 2014 Posts: 1,222 MN	Sorry Taxi...it's an SDS Plus Masonry bit for use in frost/hard ground. Shank has slots milled lengthwise in it (for the sds chuck). Taxi-it's the same setup you use, just a Millwaukee. Was just wondering if there is an auger bit with the sds shank. LDW-great idea. I'll start chasing a couple down, and do the same. Thanks! Last edited by yukonal; 10/04/19 02:39 PM.

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6632859 10/04/19 08:54 PM 10/04/19 08:54 PM
Joined: Mar 2010 Posts: 3,398 SD Boone Liane trapper
Boone Liane trapper Joined: Mar 2010 Posts: 3,398 SD	Whatever you do, Bosch bits are far superior to Dewalt!

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6632963 10/04/19 11:53 PM 10/04/19 11:53 PM
Joined: Aug 2010 Posts: 2,302 Georgia D Doug66 trapper
Doug66 trapper D Joined: Aug 2010 Posts: 2,302 Georgia	Tom Stalker....Stalker Fabrication

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6633945 10/06/19 10:51 AM 10/06/19 10:51 AM
Joined: Jan 2007 Posts: 5,459 Montana Taximan trapper
Taximan trapper Joined: Jan 2007 Posts: 5,459 Montana	I bought a keyless chuck that is made to snap in to the SDS Plus chuck on the rotary hammer.I just leave the keyless chuck attached to the auger.Sorry,I can't post pictures right now.

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6633969 10/06/19 11:19 AM 10/06/19 11:19 AM
Joined: Dec 2014 Posts: 1,222 MN Y yukonal OP trapper
yukonal OP trapper Y Joined: Dec 2014 Posts: 1,222 MN	That's ok Taxi...I saw them on Amazon, when I was searching. A lot of the cheap ones had bad reviews, so I couldn't decide which one to try. If you like yours, and it's working good, let me know which one it is, and I may go that route. Yours accepts up to 1/2", I'm assuming, correct?

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6634048 10/06/19 01:42 PM 10/06/19 01:42 PM
Joined: Jan 2007 Posts: 5,459 Montana Taximan trapper
Taximan trapper Joined: Jan 2007 Posts: 5,459 Montana	Yukonal,my 2 chucks are Bosch and have worked well.I paid $35 each,a few years ago.That is still ch eaper than having an SDS Plus auger built. And yes,they are 1/2" chucks. Last edited by Taximan; 10/06/19 01:57 PM.

Re: Auger Bit For Rotary Hammer Drill [Re: yukonal] #6634101 10/06/19 03:38 PM 10/06/19 03:38 PM
Joined: Dec 2014 Posts: 1,222 MN Y yukonal OP trapper
yukonal OP trapper Y Joined: Dec 2014 Posts: 1,222 MN	Thanks for the help Taxi!

Moderated by Drifter, Wolfdog91

Powered by UBB.threads™ PHP Forum Software 7.7.1