Fur Handling Forum


No Profanity *** No Flaming *** No Advertising *** No Anti Trappers *** No Politics
No Non-Target Catches *** No Links to Anti-trapping Sites *** No Avoiding Profanity Filter


Home~Trap Talk~ADC Forum~Trap Shed~Wilderness Trapping~International Trappers~Fur Handling

Auction Forum~Trapper Tips~Links~Gallery~Basic Sets~Convention Calendar~Chat~ Trap Collecting Forum

Trapper's Humor~Strictly Trapping~Fur Buyers Directory~Mugshots~Fur Sale Directory~Wildcrafting

Trapper's Tales~Words From The Past~Legends~Archives~Kids Forum~Lure Formulators Forum


~Dobbins' Catalog~

>
pcsoutdoors
(Please support PCS Outdoors, our sponsor for the Fur Handling Forum Page)


Print Thread
Hop To
Fur Tumbler completes plans #6344628
10/10/18 09:59 AM
10/10/18 09:59 AM
Joined: Oct 2018
Posts: 5
Jetmore Ks USA
K
kade sherrill Offline OP
trapper
kade sherrill  Offline OP
trapper
K

Joined: Oct 2018
Posts: 5
Jetmore Ks USA
Looking to build fur tumbler no 55 barrel or dryer wanting 4x6 tumbler seen few ideas in the archives but need lil more direction seen one with 1/4 hp old byxycle wheel as pulley on drum wanting one like this but then was told by another that 1/4 hp isnít big enough and also donít know what final rpms should be looking for everyoneís opinion need to know what. Route I should go cheapest is best please and thank you all for any tips or direction

Re: Fur Tumbler completes plans [Re: kade sherrill] #6346335
10/13/18 01:07 AM
10/13/18 01:07 AM
Joined: Apr 2014
Posts: 4,001
MO
cfowler Offline
trapper
cfowler  Offline
trapper

Joined: Apr 2014
Posts: 4,001
MO
I embarked on a similar adventure this year. To build a tumbler. How to do it is a bigger issue than initially thought. These aren't very good pics, but PM me, and I'll take some video if you want a better look kade. These may give you some ideas, and some food for thought.

This is a gear reduced motor turning at 12rpm. With the lower gear on the tumbler shaft, I achieved about 16. I initially had an issue with the mounting bracket and being able to keep tension on the belt, and keeping the belt straight. I personally like Monster Toms motor and drive assembly, and, I believe my stand will accommodate such an adaption later. For the time I have resolved the issue and run at 12rpm.

My tumbler drum is 4' tall and 24" on the inside. The height of my stand allows me to stand up inside the drum, from the floor, and vacuum it out. The height of my stand would accommodate a 6' drum. I will say that, you begin adding a lot of weight to the outer portions of the drum with paddles and doors, these effect the balance of the drum itself, and the torque needed to initiate turning. Add into that, a media of sawdust or something similar, with several furs, and weight and torque are major considerations. Monster Toms motor location and drive assembly both take advantage of the weight factor, where the weight of the drum contents would ensure better/full contact with what I'd call a friction-drive (cause I don't know what to call it).

The base of my stand is adjustable, one side slides inside the other square tubing on the bottom, with two bolts welded in on each side to set it.

Couple pics of the solid door and the screen for the drum, before being placed in the stand.



12" plates with 3/4" axel welded on them. Four lag bolts hold them on. The lag bolt heads are covered on the inside of the drum by FRP, a bathroom wall product, fiberglass based. I also used this as the outer covering. I would consider other products for the outer drum shell. The FRP is doing fine for the size drum I have, but a larger drum I'd want a heavier/stiffer material.

Door opening construction. I used a pvc product that resembles wood. Aztec was the brand name. These were scrap pieces from construction jobs. It's a durable, easy to work with product.

My door is much wider than the opening. I wanted to reduce as much dust as possible, because they produce dust if you run dry fur and dry media. More noticeably I should say. The edges of my door actually fit snuggly against the drum wall on both sides. It helps I believe. Plus it eliminated two edges inside the drum that fur could possibly snag on.

Depending on your skill level with tools and projects, I'd look before I leapt. It's not cheap unless you have a lot of stuff just laying around, and the ability to use it. If you're up to the challenge I say go for it. Definitely have some well thought out plans going in. Hope this helps.


I trap for fun. I skin 'em for the money!
Grinners For Life-Lifetime Member, MO Chapter, Den #1
~You Grin, You're In~
Re: Fur Tumbler completes plans [Re: kade sherrill] #6350003
10/17/18 07:19 PM
10/17/18 07:19 PM
Joined: Jun 2010
Posts: 6,842
Iowa
~ADC~ Online content
The Count
~ADC~  Online Content
The Count

Joined: Jun 2010
Posts: 6,842
Iowa
Now,,, if you're really serious about a tumbler!!!


Re: Fur Tumbler completes plans [Re: kade sherrill] #6351829
10/19/18 08:24 PM
10/19/18 08:24 PM
Joined: Apr 2014
Posts: 4,001
MO
cfowler Offline
trapper
cfowler  Offline
trapper

Joined: Apr 2014
Posts: 4,001
MO
THAT'S a tumbler! Thanks ADC, cool stuff!


I trap for fun. I skin 'em for the money!
Grinners For Life-Lifetime Member, MO Chapter, Den #1
~You Grin, You're In~
Re: Fur Tumbler completes plans [Re: kade sherrill] #6352116
10/20/18 08:59 AM
10/20/18 08:59 AM
Joined: Jan 2016
Posts: 380
New Hampshire
T
Terrence j Offline
trapper
Terrence j  Offline
trapper
T

Joined: Jan 2016
Posts: 380
New Hampshire
I just got a electric dryer that once my knee heels up from surgery I will be making a tumbler .

Re: Fur Tumbler completes plans [Re: kade sherrill] #6353038
10/21/18 02:57 PM
10/21/18 02:57 PM
Joined: Apr 2014
Posts: 4,001
MO
cfowler Offline
trapper
cfowler  Offline
trapper

Joined: Apr 2014
Posts: 4,001
MO
Electric dryers work, just depends on what your use is, and how many furs you want to do at once. Definitely a less expensive route for something to clean and fluff some fur. Tumblers ain't any different than the rest of trapping. We all got what we use, what we like best, what we prefer, what the situation dictated, but we all find a way to make it work for us. Like seeing and hearing the different things trappers have come up with.


I trap for fun. I skin 'em for the money!
Grinners For Life-Lifetime Member, MO Chapter, Den #1
~You Grin, You're In~
Re: Fur Tumbler completes plans [Re: kade sherrill] #6353171
10/21/18 06:45 PM
10/21/18 06:45 PM
Joined: Jan 2016
Posts: 380
New Hampshire
T
Terrence j Offline
trapper
Terrence j  Offline
trapper
T

Joined: Jan 2016
Posts: 380
New Hampshire
Well I was washing on a gentle rince cycle in an old washing machine butit takes way to long for them to dry so hopefully this will help speed up my really dirty fur put up.

Re: Fur Tumbler completes plans [Re: kade sherrill] #6354478
10/23/18 09:49 AM
10/23/18 09:49 AM
Joined: Oct 2018
Posts: 5
Jetmore Ks USA
K
kade sherrill Offline OP
trapper
kade sherrill  Offline OP
trapper
K

Joined: Oct 2018
Posts: 5
Jetmore Ks USA

Re: Fur Tumbler completes plans [Re: kade sherrill] #6354479
10/23/18 09:50 AM
10/23/18 09:50 AM
Joined: Oct 2018
Posts: 5
Jetmore Ks USA
K
kade sherrill Offline OP
trapper
kade sherrill  Offline OP
trapper
K

Joined: Oct 2018
Posts: 5
Jetmore Ks USA
comin together have all built now beside my belts but cant upload that pic says to big

Re: Fur Tumbler completes plans [Re: kade sherrill] #6354482
10/23/18 09:57 AM
10/23/18 09:57 AM
Joined: Oct 2018
Posts: 5
Jetmore Ks USA
K
kade sherrill Offline OP
trapper
kade sherrill  Offline OP
trapper
K

Joined: Oct 2018
Posts: 5
Jetmore Ks USA

Re: Fur Tumbler completes plans [Re: kade sherrill] #6357092
10/26/18 09:30 AM
10/26/18 09:30 AM
Joined: Apr 2014
Posts: 4,001
MO
cfowler Offline
trapper
cfowler  Offline
trapper

Joined: Apr 2014
Posts: 4,001
MO
It's looking good Kade. Flipped it, so I could see it a little better.

What is your rpm? Keep us posted as you get it finished! I enjoy following projects like this. Learn as much as I share, if not more.


I trap for fun. I skin 'em for the money!
Grinners For Life-Lifetime Member, MO Chapter, Den #1
~You Grin, You're In~
Previous Thread
Index
Next Thread

Powered by UBB.threads™ PHP Forum Software 7.7.1